Choose the blade to suit the purpose. These blades are designed so that heat is concentrated along the cutting edge in order to achieve the optimum cutting temperature. Prior to insertion in the material to be cut, the temperature of the blades will be between 100°C and 800°C, depending on the type of blade and the thermocutter used. The temperature to the blade cools down as it enters the material. The temperature depends on the thermal properties and heat conductivity of the material being cut and determines the cutting speed. The cutting edge is evenly heated because of the design of the blade's cutting flanges.

Blades with model numbers in green are only for use with the Zetz-24 and 25 Thermocutters.

Model T 3 These are the most commonly used blades. Blades Thickness Cutting Edge Length T 3/15 0.6 mm 15 mm T 3/30 0.6 mm 30 mm T 3/50 0.6 mm 50 mm T 3/90 0.6 mm 90 mm T 3/125 0.6 mm 125 mm Model T 2 Sharpened on two sides to prevent distortion, allows cutting in two directions. Ideal for cutting foam. T2/50 for trimming laminated solar panels. Blades Thickness Cutting Edge Length T 2/50 0.6 mm 50 mm T 2/100 0.6 mm 100 mm T 2/150 0.6 mm 150 mm T 2/200 0.6 mm 200 mm Model T 11 With angled cutting edge and a parrot's beak to serve as a guide hook. Blades Thickness Cutting Edge Length T 11/15 0.6 mm 15 mm T 11/30 0.6 mm 30 mm Model T-4 Snub nosed design allows for concentrated heat at the tip. Blades Thickness Cutting Edge Length T-4 0.6 mm 30 mm Model T 015 Blades listed below are spade shaped to be held verically. Suitable for mounting installations. Blades Thickness Cutting Edge Length T 015/.6 0.6 mm 35 mm T 015/.8 0.8 mm 35 mm T 015/1.0 1.0 mm 35 mm Back to AZTC-20 Back to ZETZ-9 Back to ZETZ-24 Examples of uses for blade numbers—T-2, T-3, T-11, T-01, T-02,T-04, T-05, T-06, T-10, T-08, T-015, T-011, T-012, T-013, V-1 Cutting and de-burring of: Natural and synthetic rubber Rubber sheets 30-80 Shore Rubber with textile PVC boards, foils and sheets Cutting off and heat sealing fabric piles, industrial tubings, profile gaskets. Car trim and upholstery, cutouts in instrument panels. Roof and wall insulation boards up to 125 mm thickness of foam PE, PS, PU. No gap, no cold bridge. Cutting out silicone gaskets for construction joints. Floor and wall claddings, including bituminous materials. Stress-free cutting of profile gaskets of PVC and Neoprene rubber for window and door frames. Clean cuts for subsequent welding or gluing. Electrical installations like conduit and trunking channels. Insulating cables and leads. Model T 01 With glide hooks that hook into the material and glides along cutting base. T 02 and T02S0 for trimming laminated solar panels. T 02S0 is offset at 90° angle. Blades Thickness Cutting Edge Length T 01 0.6 mm 6 mm T 02 0.8 mm 12 mm T 02S0 1.0 mm 12 mm Model T 04 With short, obtuse angled cutting edges, both sides are ground. Blades Thickness Cutting Edge Length T 04 0.6 mm 15 mm Model T 05 With wide blade back and reinforced cutting flange. Stable cutting. The high temperature blade is designed for heat sealing the cutting edges. For trimming laminated solar panels. Blades Thickness Cutting Edge Length T 05 0.6 mm 35 mm Model T 011 Standard blades, double edged, with concave cutting edges leading to a point— For cutting material at an oblique angle and at a high temperature. Can achieve a small radius on rounded cuts. Cuts staight into material without preparatory drilling. De-burring blade for anti-static trimming of excess plastic from sprues without waste or tension cracks. Blades Thickness Cutting Edge Length T 011/.6 0.6 mm 10 mm T 011/.8 0.8 mm 10 mm Model T 12 With long pointed blade flanges, ground both sides. For two-directional cuts. For cutting around templates. Also suitable for de-burring. T012/1.0 for trimming laminated solar panels. Blades Thickness Cutting Edge Length T 012/.6 0.6 mm 35 mm T 012/1.0 1.0 mm 35 mm Model V-1 Used for sheet plastics, asphalt roofing paper, roll stock and any high-heat application— Not designed fo continuous use. Blades Thickness Cutting Edge Length V-1* 2.0 mm 15 mm *For use with the Zetz-24 only. Back to AZTC-20 Back to ZETZ-9 Back to ZETZ-24 Model T 06 With a rounded edge to glide along cutting surface Heat sealing the edges to prevent fraying of synthetic fibers and textiles. Blades Thickness Cutting Edge Length T 06 0.6 mm 2 mm Model T 150 Cutting Sling consists of adjustable arms plus Blade No. T 151 which can be reshaped once. Applications: For rounded, angular, concave and other shaped cuts. Shaping interior spaces, cutting hollows into foam materials such as PE, PS, PU, etc.. Cutting Sling Thickness Blade Length T 150 Replacement Blade (T 151) .05 mm 15 cm Model Tn 106 Grooving (for use with Cutting Sling) for quick cutting of grooves and flutes in foam materials made of PE, PS, PU. Blades Thickness Cutting Edge Length Tn 106 16-22 mm 16 mm Model T 013 & ATL Blades have curved cutting edge and thick blade. High temperature blade suitable for long cuts under pressure. ATL Blades are the same as T013 Blades with the exception of being offset at a 45° angle. Blades Thickness Cutting Edge Length T 013/45 0.8 mm 45 mm T 013/70* 1.0 mm 70 mm T 013/115* 1.0 mm 115 mm ATL/45 0.8 mm 45 mm ATL/70 1.0mm 70 mm *For use with the Zetz-24 only. Back to AZTC-20 Back to ZETZ-9 Back to ZETZ-24 Blade T 08 Gives a clean cut which allows seamless joining of material in subsequent sealing or gluing operations. With evenly heated cutting edge and thick blade From 50 mm cutting length upwards. Suitable for thermoplastics with low melting points such as foam polyethylene, polystyrene, polyurethane. Roof and wall insulation boards up to 120 mm thickness. No gap, no cold bridge. Cutting profile gaskets of PVC and Neoprene rubber for windows and door frames without crushing the material. Blades Thickness Cutting Edge Length T 08/50 0.8 mm 50 mm T 08/75* 0.8 mm 75 mm T 08/100* 0.8 mm 100 mm T 08/120* 0.8 mm 120 mm *For use with the ZETZ-24 ONLY Thermocutter Blades Continued>>

BLADES for AZTC-20, ZETZ-9 and ZETZ-24 THERMOCUTTERS:

Complementary Products:

AZTC-20 Compact Thermocutter-. ZETZ-9 Compact Thermocutter-. ZETZ-24 Thermocutter-Thermocutter with Standard Handle. ZETZ-25 Thermocutter with Robotic Hand-Thermocutter Control Unit with EOAT Handle. Thermocutter Foot Attachment-. BLADES for AZTC-20, ZETZ-9 and ZETZ-24 THERMOCUTTERS-.

We accept: -Check -Money Order -Purchase Order

-List All Products | -View Cart
©2010 Abbeon Cal, Inc. 123 Gray Avenue Santa Barbara, CA 93101-1809