b'AZTC-20 and ZETZ-24/25 THERMOCUTTERBLADEST hese blades are designed so that heat is concentratedThermocutter used. The temperature of the blade cools along the cutting edge for the optimum cuttingdown as it enters the material. The temperature is affected temperature. Before inserting in the material to be cut,by the thermal properties and heat conductivity of the the temperature of the blades will be between 200Fmaterial being cut and determines the cutting speed.and 1400F, depending on the type of blade and the Uses Blades Thickness Cutting PriceEdgeLengthNo.T3-15P0.6 mm15 mmPkg of 6/ $ 69 24Standard blade used for many simpleNo.T3-30P0.6 mm30 mmPkg of 6/ $ 69 24cutting applications. No.T3-50P0.6 mm50 mmPkg of 6/ $ 69 24No.T3-90P0.6 mm90 mmPkg of 2/ $ 24 51No.T3-125P0.6 mm125 mmPkg of 2/ $ 24 51Sharpened on two sides to prevent distortion, allows cutting in two directions. Ideal for cut- No.T2-50P0.6 mm50 mmPkg of 6/ $ 75 26ting foam. T2/50 for trimming laminated No.T2-100P0.6 mm100 mmPkg of 2/ $ 28 22solar panels. No.T2-150P0.6 mm150 mmPkg of 2/ $ 28 22No.T2-200P0.6 mm200 mmPkg of 2/ $ 32 00With angled cutting edge and parrots beak toNo.T11-15P0.6 mm15mm/30mmPkg of 6/ $ 78 87serve as guide hook. No.T11-30P0.6 mm30mm/30mmPkg of 6/ $ 78 87Spade shaped to be held vertically. SuitableNo.T015-0-60.6 mm35 mm$ 18 22 /eafor mounting installations.T015/1.0 for trimmingNo.T015-0-80.8 mm35 mm$ 19 13 /ealaminated solar panels. Available bladeNo.T015-1-01.0 mm 35 mm$ 20 53 /eathickness: 0.6 mm, 0.8 mm, 1.0 mmWith Glide Hook. Hooks into material and glidesNo.T010.6 mm6 mm $18 27 /eaalong cutting base.T 02 and T02S0 for trimming laminated solar pan els. No. T 02S0 is offset atNo.T020.8 mm12 mm$ 18 27 /ea90 angle. No.T02SO1.0 mm12 mm$ 25 96 /eaWith short, obtuse angled cutting edges, bothNo.T040.6 mm15 mm$ 18 27 /easides ground.Wide blade back and reinforced cutting flange for stable cutting.This high temperature bladeNo.T050.6 mm35 mm$ 18 27 /eais designed for heat sealing the cut edges. For trimming laminated solar panels.Standard blade, double edged, with concaveNo.T011-0-60.6 mm10 mm$ 18 27 /eacutting edges leading to a point For cutting material at an oblique angle and at a highNo.T011-0-80.8 mm10 mm$ 19 13 /eatemperature. Deburring blade.Long pointed blade flanges, ground both sidesNo.T012-0-60.6 mm35 mm$ 19 89 /eafor two-directional cuts. For cutting aroundNo.T012-0-80.8 mm35 mm$ 19 89 /eatemplates. Also suitable for deburring.T012/1.0 for trimming laminated solar panels. No.T012-1-01.0 mm35 mm$ 21 39 /eaUsed for sheet plastics, asphalt roofing paper, roll stock and any high-heat application. NotNo. DPM102.0 mm15 mm$ 27 74 /eadesigned for continuous use. ZETZ-24/25 only.4 Abbeon Cal, Inc. 1363 Donlon Street Unit 1, Ventura CA 93003 Catalog 122P'