Specialty Blades for AZTC20 and ZETZ24 Thermocutters (Hot knives)

See all items from Thermocutters
Product Description

Specialty Blades for AZTC20 and ZETZ24 Thermocutters (Hot knives)
Choose the Hot Knife blade to suit the purpose. These Hot Knife blades are designed so that heat is concentrated along the cutting edge in order to achieve the optimum cutting temperature. Prior to insertion in the material to be cut, the temperature of the blades will be between 100°C and 800°C, depending on the type of blade and the Thermocutter used. The temperature to the Hot knife blade cools down as it enters the material. The temperature depends on the thermal properties and heat conductivity of the material being cut and determines the cutting speed. The cutting edge is evenly heated because of the design of the blade's cutting flanges.

Blades with model numbers in green are for use only with the ZETZ-24 Hot knife and 25 Hot knife Thermocutters.

  • Suitable for thermoplastics with higher melting points such as rubber, synthetic rubber, synthetic resins
  • Cutting rubber up to 90 Shore combustible, oil resistant rubber.
  • Cutting out rubber linings on containers, mixers, vibration and, conveyor chutes and troughs.
  • Angled cuts at joints on conveyor belts, camelbacks, rubber anti-abrasion coatings.
  • Cutting and peeling rubber sectioning belts and flexible PVC (supported or unsupported).
Blades are designed for rapid heating to maximum temperature
The entire cutting edge must be used in the material to obtain full benefit of the heat and to maximize cutting efficiency. Blades are available in 5 cutting lengths and should be chosen according to thickness of material.
Blades Thickness Cutting Edge Length
T 10 1.0 mm 10 mm
T 15 1.0 mm 15 mm
T 30 1.0 mm 30 mm

Specialty Thermocutter Hot Knife Blades

Ideal for removal of adhesive material or removal of plastic flashings. Scoop design with 1/8" sides.
Blades Thickness Cutting Edge Length
ATS 10 0.8 mm 10 mm
ATS 18 1.0 mm 18 mm

Heavy duty blade designed for removing plastic/rubber linings inside storage tanks. Scoop design with 3/8" sides. For use with ZETZ-24/25 only.
Blades Thickness Cutting Edge Length
TS 30 1.0 mm 30 mm
TS 30SB45 1.0 mm 45 mm
TS 30SB60 1.0 mm 60 mm

Blades for cutting insulating material. Thick blade for controlled cutting, with constant temperature along the cutting edge. Blades available in 7 lengths, should be chosen according to thickness of material. For a length of more than 100 mm, use only on ZETZ-24/25 Hot Knife.

--For anyone using foam insulation such as contractors, painters, interior fitters, insulating specialists.

--Roof and wall insulation boards up to 200 mm thickness made of PE, PS, PU.

--Quick and neat joining and fitting of insulation boards. Cutting time for 1 m long, 150 thick insulation board is 8 seconds.
Blades Thickness Cutting Edge Length
DT 50 1.0 mm 50 mm
DT 100 1.0 mm 100 mm
DT 150 1.0 mm 150 mm
DT 200 1.0 mm 200 mm

GridItemIDItem NoItem InformationThicknessCutting Edge LengthPriceOrder Qty
165T10Rapid heated max temp blade 10mm1.0mm10mm
166T15Rapid heated max temp blade 15mm1.0mm15mm
180T30Rapid heated max temp blade 30mm
AZ-TC Thermocutter Hot Knife Blade
355ATS10Plastic flash and adhesives removal 10mm blade0.8mm10mm
356ATS18Plastic flash and adhesives removal 18mm blade1.0mm18mm
41TS30Heavy duty 30mm blade for removing plastic linings in storage tanks1.0mm30mm
6025TS30SB45Heavy duty 45mm blade for removing plastic linings in storage tanks1.0mm45mm
6026TS30SB60Heavy duty 60mm blade for removing plastic linings in storage tanks1.0mm60mm
382DT50Insulation cutting 50mm blade1.0mm50mm
377DT100Insulation cutting 100mm blade1.0mm100mm
379DT150Insulation cutting 150mm blade1.0mm150mm
381DT200Insulation cutting 200mm blade1.0mm200mm